Corrugated Metal Roofing
Our local roofer installs and repairs corrugated metal roofs on houses, garages and pole sheds around North Branch. These are the wavy, screw-down panels, the most affordable way into metal roofing. They need the right screws, trim and underlayment for a Minnesota winter.
What Corrugated Metal Roofing Is
Corrugated metal roofing is a sheet of steel or aluminum rolled into a repeating wave or ribbed pattern and fastened through the face of the panel with screws that carry rubber sealing washers.
The ribs give a thin sheet its strength, so panels can span between wood strips or purlins on a shed, or lie over a solid deck and underlayment on a house. Most steel panels sold today are painted over a metallic coating such as the aluminum-zinc coating on a Galvalume metal roof.
Key difference
Exposed fasteners
Every screw goes through the panel face, so the washers are the part to watch over the years.
What Corrugated Metal Roofing Costs
Corrugated metal roofing costs about $3.50 to $15 per square foot installed in one national range and $3.50 to $26 in another. That makes it the lowest-cost metal profile in both, and neither figure is a quote.
The top of the wider range reflects heavier gauges, premium paint and complex houses. A simple garage roof with long straight runs sits near the bottom. Tear-off, new decking and trim add to any figure, and our local roofer prices your building after seeing it.
Corrugated vs other metal profiles
Installed, per sq ftWant a real price for corrugated metal roofing?
Our local roofer will look at your roof and give you a written estimate. Send a few details or call (651) 427-2051.
Corrugated Metal vs Standing Seam
Corrugated metal costs less than standing seam because its screws go through the panel face, while standing seam hides its fasteners under raised seams and needs less upkeep over its life.
On a garage or shed, corrugated is usually the sensible pick. On a house you plan to keep for decades, many owners weigh the lower price of corrugated against the cleaner look and fewer exposed screws of a standing seam metal roof.
Corrugated
- Lowest cost metal profile
- Screws and washers exposed to weather
- Washers age and screws may need re-tightening
- Fast to install on simple roofs
- Rustic or farm look
Standing seam
- Higher cost per square foot
- Fasteners hidden under the seams
- Clips let panels move with temperature
- Better suited to low slopes
- Clean, modern look
Where Corrugated Metal Roofing Works Best
Corrugated metal roofing works best on detached garages, pole sheds, workshops and simple gable houses where long straight panels can run from ridge to eave without many cuts.
Every valley, dormer and chimney means more cut panels, more trim and more places to seal. On a cut-up house roof, a smaller-format product such as stone-coated steel roofing often fits better.
Detached garages
A detached garage counts as residential real estate under Minnesota law, so roofing it for pay still needs a licensed roofer.
Sheds and outbuildings
Minnesota's ice barrier rule exempts detached accessory structures with no conditioned floor area.
Simple houses
A plain gable or hip roof on a house can take corrugated over a solid deck, with the full ice barrier the code requires at the eaves.
Porches and lean-tos
Small add-on roofs often use corrugated, though a copper roof is the upscale choice for a porch or bay window on the front of a house.
Want our local roofer to take a look?
Send a few details or call (651) 427-2051, and our local roofer will come and look.
Common Corrugated Roof Problems
The most common corrugated roof problems are screws that back out, rubber washers that crack with age, leaks at panel side laps and rust where cut edges or scratches expose bare steel.
None of these mean the roof is finished. They are maintenance items, and catching them early is far cheaper than waiting for a soaked deck or framing. If you see any of these signs, ask about metal roof repair.
- Screw heads standing proud of the panel
- Cracked or flattened washers
- Drips along a panel lap after rain
- Rust streaks below screws or at cut ends
- Frost or dripping under panels in an unheated building
Check yearly
Screws and washers
A quick look each fall at the fasteners catches most corrugated leaks before winter.
How Corrugated Metal Is Installed on a Home
Corrugated metal is installed on a home by preparing a solid deck, laying ice barrier and underlayment, fitting eave trim, then screwing panels down in lapped rows before the ridge cap and flashing go on.
North Branch requires a reroofing permit for a house, and the city inspects the deck and ice barrier at tear-off.
- 1
Deck and underlayment
Old roofing comes off, damaged decking is replaced, and ice barrier goes from the eave to at least 24 inches inside the exterior wall.
- 2
Trim at the edges
Eave and rake trim go on first so water running off the panels drops clear of the fascia.
- 3
Panels and screws
Panels are laid with side laps facing away from the prevailing wind and screwed in the pattern the manufacturer specifies.
- 4
Ridge, flashing and boots
Ridge cap with closure strips, chimney and wall flashing, and pipe boots finish the roof before the final inspection.
Corrugated Metal Roofing FAQs
Can corrugated metal be used on a house?
Yes, corrugated metal can be used on a house when it goes over a solid deck with the ice barrier and underlayment Minnesota requires. It suits simple roof shapes best.
How much does a corrugated metal roof cost?
About $3.50 to $15 per square foot installed in one national range, or $3.50 to $26 in another. Neither is a quote. Our local roofer prices your roof after seeing it.
Do corrugated roof screws need replacing?
Sometimes, yes. The rubber washers under exposed screws age in sun and cold, so screws on an older corrugated roof may need re-tightening or replacing with a larger size.
Does my pole shed need ice and water shield?
Not by code if it is a detached accessory structure with no conditioned floor area, which Minnesota's ice barrier rule exempts. A heated shop is different, and the roofer can explain the options.
Is corrugated metal noisy?
Yes, corrugated panels screwed to open purlins over an unheated building are noisy in rain and hail. Over a solid deck and underlayment on a house, the noise is much lower.
Get a corrugated metal estimate
Tell us whether it is a house, garage or shed and roughly how big. Our local roofer will look at your roof and give you a price.
Call now (651) 427-2051 Roofing in North Branch and the towns around it