Standing Seam Metal Roofs
Our local roofer installs and repairs standing seam metal roofs on North Branch homes. These panel roofs have raised seams from ridge to eave and no screw heads on the surface. They are the most common choice for a whole-house metal roof.
What a Standing Seam Metal Roof Is
A standing seam metal roof is made of long vertical metal panels whose edges rise and lock together into raised seams, with the panels held down by clips or fastening flanges hidden inside those seams.
Because nothing pierces the flat of the panel, there are no exposed screws and washers to age. The clips also let each panel expand and contract with temperature, which matters on a roof that goes from a hot July afternoon to a January night.
Main advantage
Hidden fasteners
No screw holes through the panel face means fewer places for water to get in.
What a Standing Seam Metal Roof Costs
A standing seam metal roof costs about $15,100 for a basic 1,500 sq ft roof in Minneapolis, within a range of $11,800 to $18,500. That is a local figure and not a quote for your North Branch house.
Minneapolis metal roofs run $8 to $12 per square foot installed, without splitting out the metal. Per square foot, the metal makes the biggest difference. Nationally, steel runs $10 to $16, aluminum $11 to $18, and copper or zinc $25 to $35. Roof size, pitch, valleys, tear-off and decking repairs all change the total.
Standing seam by metal, national ranges
Installed, per sq ftWant a real price for standing seam metal roofs?
Our local roofer will look at your roof and give you a written estimate. Send a few details or call (651) 427-2051.
How Long a Standing Seam Roof Lasts
A standing seam roof lasts about 50 to 80 years in most cases, and copper or zinc standing seam can approach 100 years.
That is longer than the general 40 to 70 year range for metal roofs overall, mostly because there are no exposed fasteners to wear out. Flashing at chimneys and walls, and pipe boots, still need attention over that time.
Snow Sliding Off a Standing Seam Roof
Snow slides off a standing seam roof in large sheets once it loosens, because the smooth panels give it nothing to hold onto, so the roof needs snow guards anywhere falling snow could hit people, doors, decks or lower roofs.
Plan this before the panels go on, since guards clamp to the seams and are laid out with the roof. See roof snow guards for the options. Scraping a roof or chipping ice can damage it, so avoid metal tools on the panels.
- Entry doors and steps under an eave
- Decks, patios and walkways
- Gutters along the eave edge
- Lower roofs, sunrooms and porches below
- Cars, meters and AC units against the house
Plan ahead
Snow guards
Seam-clamped guards hold snow so it melts off slowly instead of avalanching.
How a Standing Seam Roof Is Installed
A standing seam roof is installed by stripping the old roof to the deck, laying ice barrier and high-temperature underlayment, fitting trim, then clipping each measured panel in place and closing the seams before the ridge and flashing go on.
In North Branch the reroof needs a city permit, and the inspector checks the deck and the ice barrier at tear-off.
- 1
Measure and order
Panels are cut to the length of each roof run, so the roofer measures carefully before ordering.
- 2
Tear-off and deck
Old roofing comes off and any soft decking is replaced so the panels lie flat.
- 3
Ice barrier and underlayment
Minnesota requires ice barrier from the eave to at least 24 inches inside the exterior wall; see ice and water shield.
- 4
Panels and seams
Each panel is clipped down and the seams are snapped or mechanically folded closed.
- 5
Ridge, flashing and guards
Ridge cap, wall and chimney flashing, pipe boots and snow guards finish the roof before the final inspection.
Want our local roofer to take a look?
Send a few details or call (651) 427-2051, and our local roofer will come and look.
Standing Seam vs Exposed-Fastener Metal
Standing seam costs more than exposed-fastener metal such as corrugated panels, but it hides its fasteners and lets panels move with temperature, so it needs less upkeep over its life.
For a garage, shed or tight budget, corrugated metal roofing is often enough. For the house you plan to keep, standing seam is the usual pick.
Exposed fastener
- Screws through the panel face
- Washers age and need checking
- Lower cost
- Common on outbuildings
Standing seam
- Fasteners hidden in the seams
- Panels float on clips
- Higher cost
- Common on homes
Standing Seam Metal Roof FAQs
How much does a standing seam metal roof cost?
About $15,100 for a basic 1,500 sq ft roof in Minneapolis, within $11,800 to $18,500. Nationally, the average is $19,000, with most jobs between $9,400 and $32,600. Neither is a quote; the roofer prices your roof after seeing it.
Do I need snow guards on a standing seam roof?
Yes, in most cases, anywhere snow sliding off could land on people, doors, decks, gutters or a lower roof. Standing seam sheds snow readily, so guards are part of a sensible Minnesota install.
Can standing seam go on a low-slope roof?
Yes, standing seam works on lower slopes than shingles, because the raised seams keep water off the joints. The manufacturer sets the minimum slope for each panel.
Can a standing seam roof be repaired?
Yes, damaged panels, seams, flashing and boots can be repaired, though a badly damaged panel is often replaced along its full length. See metal roof repair.
Is standing seam better than metal shingles?
Neither is better for every house: standing seam suits simpler roofs and a modern look, while metal shingles suit cut-up roofs and a traditional look.
Get a standing seam estimate
Send a few details about your roof and the metal you are leaning toward. Our local roofer will measure it and price a standing seam roof.
Call now (651) 427-2051 Roofing in North Branch and the towns around it