Drip Edge Installation

Our local roofer installs drip edge on North Branch homes, usually during a reroof and sometimes on its own. Drip edge is a strip of bent metal along the eaves and rakes. It makes water drip clear of the fascia and into the gutter.

Request a Roof Inspection

Fill in the form below or call us now on (651) 427-2051

Best way to reach you

Thanks, we've passed your request to our local roofer and they'll be in touch shortly.

Is Drip Edge Required in Minnesota?

Drip edge is not required by the residential building code in Minnesota. The state deleted the drip edge section from its version of the code.

So a North Branch roof without drip edge can pass inspection.

Not required is not the same as not useful. The code sets a minimum. The shingle maker's installation instructions are a separate document, so ask the roofer what the instructions for your chosen shingle say about the roof edge.

Drip edge rule

Not required

Minnesota deleted the drip edge rule from its residential code.

What Drip Edge Does on a Roof

Drip edge on a roof carries water off the shingle edge and away from the fascia and deck, supports the overhanging edge of the shingles, and closes the gap between the roof deck and the fascia board.

Protects the fascia

Water clings to a bare shingle edge and runs back onto the fascia board, which is how fascia rots. See soffit and fascia if yours already has.

Feeds the gutter

The metal lip drops water out past the fascia so it lands in the gutter instead of dribbling down behind it. See gutter installation.

Supports the shingle edge

The first course of shingles overhangs the deck, and drip edge gives that overhang something firm to rest on so it doesn't droop or curl.

Closes the gap

There is often a gap between the deck edge and the fascia. Drip edge covers it, which keeps out wind-driven rain, insects and small animals.

A Roof Edge With and Without Drip Edge

A roof edge without drip edge lets water cling to the shingles and wick back onto the fascia and the end of the deck, while a roof edge with drip edge drops that water clear into the gutter.

Without drip edge

  • Water runs back under the shingle edge
  • Fascia board stays wet and rots over time
  • Deck edge can soften along the eaves
  • Water can miss the gutter and run behind it
  • Gap at the deck edge stays open to pests

With drip edge

  • Water drips clear off a metal lip
  • Fascia stays drier
  • Deck edge is covered and supported
  • Water lands in the gutter
  • Gap at the deck edge is closed

Not sure which way to go?

Our local roofer will look at your roof and tell you which option suits it. Send a few details or call (651) 427-2051.

Get Estimate →

How Drip Edge Is Installed

Drip edge is installed along the eaves before the ice barrier goes down and along the rakes after the underlayment, so that every layer laps over the one below it and water always runs on top.

  1. 1

    Check the edge

    With the old roofing off, the roofer checks the deck edge and fascia for rot and replaces bad wood first; see roof decking replacement.

  2. 2

    Eave drip edge

    Metal is nailed along the eaves with each piece lapped over the next, downhill pieces under uphill ones.

  3. 3

    Ice barrier

    In Minnesota the ice barrier runs from the eave to at least 24 inches inside the exterior wall line. It laps over the eave drip edge. See ice and water shield.

  4. 4

    Rake drip edge

    After the underlayment is on, drip edge goes along the sloped rake edges on top of it, so wind-driven rain can't get under the felt.

  5. 5

    Shingles

    The starter course and shingles are laid with a small overhang past the metal, so water drips off the shingle onto the drip edge and away.

A two-story house with a dark shingle roof, white aluminum gutters, and a downspout running down the corner

Can Drip Edge Be Added to an Existing Roof?

Drip edge can be added to an existing roof in some cases, by carefully lifting the first course of shingles at the eaves and rakes and sliding the metal underneath, but on old or brittle shingles it is usually better left for a roof replacement.

Cold shingles crack when bent, so a retrofit is a warm-weather job. If the shingles are near the end of their life, the roofer may suggest waiting and doing it right with the next roof, when the drip edge can sit under the ice barrier the way it should.

If the fascia is already rotten, it has to be fixed before new metal goes on, otherwise the drip edge is nailed into soft wood.

Retrofits

Warm weather

Lifting shingles in the cold risks cracking them.

Want our local roofer to take a look?

Send a few details or call (651) 427-2051, and our local roofer will come and look.

Get Estimate →

What Drip Edge Installation Costs

Drip edge installation cost depends on how many feet of eave and rake the roof has and whether the metal goes on with a new roof or as a separate job, and our local roofer prices it after measuring.

When drip edge goes on during a reroof, it is usually one line in the roof estimate. Under Minnesota law a licensed contractor's written contract has to describe the materials and give the price or how it is calculated, so ask to see drip edge listed if you want it.

Drip Edge Installation FAQs

Is drip edge required in North Branch?

No. Minnesota deleted the drip edge rule from its residential code, so metal drip edge is not required. It is still a good idea on most shingle roofs.

Does drip edge go over or under the ice and water shield?

Under it at the eaves and over the underlayment at the rakes. That way each layer laps over the one below and water never runs behind the membrane.

Do I need drip edge if I have gutters?

Yes, it helps. Without drip edge, water can run back along the fascia and slip behind the gutter. Drip edge puts the water out past the fascia so the gutter actually catches it.

What is drip edge made of?

Usually prefinished aluminum or galvanized steel, in a few profiles and colors. The roofer picks a profile that fits the fascia and the gutter.

How much does drip edge installation cost?

It depends on the length of the eaves and rakes and whether it goes in with a new roof. The roofer measures the roof and prices it.

Get a drip edge estimate

Tell us whether you are planning a new roof or want drip edge added to the one you have, and whether the fascia shows rot. We pass it to our local roofer, who measures and prices the job.

Call now (651) 427-2051 Roofing in North Branch and the towns around it

Request a Roof Inspection

Fill in the form below or call us now on (651) 427-2051

Best way to reach you *

Thanks, we've passed your request to our local roofer and they'll be in touch shortly.